Shop Material for this project

1 5
View all

Project Insturctions

  • Step 1

    Condition and roll Butter clay to desired thickness for slab. Mine was rolled to setting #2 on the pasta machine. (#1 is widest) Cut rectangle in desired slab size.

  • Step 2

    Place the clean fabric over the surface and press to transfer the fabric texture to the clay sheet.

  • Step 3

    Condition and roll Sunshine clay slightly thinner than Butter clay. I rolled mine to setting #3 on the clay machine.Use drop shaped cutter from Mini Geometric set to cut 2 drops for every flower you wish to create.

  • Step 4

    Use the pointed end of the drop cutter to cut two “v” shaped notches in the rounded end of each yellow drop.

  • Step 5

    Use the small oval cutter from the Mini Geometric set to cut a small section from both sides of the pointed end and make the petals slightly smaller and slightly more curved on the sides.

  • Step 6

    To create the flowers, place two petals with the ends touching as shown for each flower.

  • Step 7

    Re-roll Sunshine clay to setting #1 (widest) and use smallest Etch ‘n Pearl tool to create pearls. Place a row of pearls in an upward arc over the tops of the petals as shown.

  • Step 8

    Roll Forest Green and Spanish Olive clay to setting #3. Use leaf pattern on Nature Texture Sheet to texture both sheets of clay.

  • Step 9

    Use “lemon” shaped cutter from Mini Geometric set to cut leaves from both sheets.

  • Step 10

    I wanted my leaves slightly smaller, so I used the same cutter to trim a bit off each leaf. This is optional.Use the clay blade to cut each leaf in half lengthwise.

  • Step 11

    Gather Forest Green and Spanish Olive scraps. Allowing the colors to marble somewhat, roll together into a cylinder to fit into extruder.

  • Step 12

    Use small multi-hole disc to extrude the green clay.

  • Step 13

    Cut short pieces of the extruded clay to fit from the center of each flower up to the yellow pearls as shown.Place 3 in each flower with the ends together where the petals meet and extending outward at the top.Make tiny balls from the green clay and add them to the top of each strand you just added to the flowers.

  • Step 14

    Add strands of the extruded clay where you would like the leafed vines to be.

  • Step 15

    Add the leaves to the vines as desired. I used half of each color for each finished leaf, leaving a small space between each color.

  • Step 16

    To create the clustered green berry areas, use your fingers to carefully roll and reduce the size of one of the extruded sections of clay. Then cut small pieces and arrange them to create the clusters.Make tiny balls of the green clay and add them to the ends of each piece of the clusters for green berries.

  • Step 17

    Extrude Cowboy clay with same disc. To create the 3 “twig/berry” clusters, cut 3 small sections and arrange them as shown where you wish to add them.Make tiny balls and add them to the ends of each “twig.”

  • Step 18

    To create the tiny pale pink flowers on the vine, I combined scraps of White, Cowboy, and added in Guava in small amounts until I achieved the shade I wanted.I rolled it to create a sheet and then used my smallest Etch ‘n Pearl tool to create pearls.Each pearl was flattened, then “crumpled” a bit and added to the vine.I used the pointed end of the tool to push them in place.

  • Step 19

    To make the clusters of 3 “seeds,” I combined a small amount of the blended pink clay with more Cowboy.Roll the blended color into a small strand and cut tiny equal sections.Roll the sections into balls and use the tool to make an impression in the center of each. Add them where desired in clusters of 3, with single seeds here and there.

  • Step 20

    Use pointed end of tool to make small impressions along the bottom edge of each of the yellow flowers.I also used the tool to make 3 lines from the tip of each yellow flower petal as shown.

  • Step 21

    Use the tip of the tool to add a tiny spot of metallic gold paint to the center of the pink flowers. I left some of my flowers with a more closed effect and did not add paint to those.

  • Step 22

    Add the leaf charms (if desired) to small jump rings.Add slightly larger jump rings to the earrings.Add a small jump ring to the earring wire.Loop the jump ring through the larger ring attached to the earring.Add the small jump ring with the charm to the front of the wire so it hangs in front of the earring.
1 22